Skip to content
72hr Delivery Book a Flight

What during production inspection (dpi) covers beyond visual checks: part 2

a
admin
Field Notes
Published Estimated read · 8 min
The short answer

Regulated goods need compliance checkpoints inside the production visit, not just after it. Materials get substituted, markings get simplified, and each quiet change can void the earlier test approval. Checking substance controls and marking conformity while the line runs keeps the order sellable in its destination market.

Key takeawaysProduction substitution is the classic compliance failure, so verify material identity on the line rather than trusting the approval sample alone. · RoHS limits specific hazardous substances in electrical goods, and only testing of production units can confirm the limits are met [1]. · CE marking rules require correct marking, warnings, and instructions, all verifiable visually during production [2]. · UTS inspectors document conformity evidence for the buyer but do not issue regulatory certificates or redesign products. · Pair every production visit on regulated goods with laboratory testing of samples drawn from the same run.

For unregulated goods, a production defect means returns and rework. For regulated products, the same defect can mean the goods cannot legally be sold in the destination market. Restricted substances, marking obligations, and safety requirements add a compliance layer to every in-production checkpoint.

Many buyers assume compliance was settled when the pre-production sample passed testing. Production tells a different story: materials get substituted, markings get simplified, and warnings get shortened to fit smaller packaging. Each change can silently void the earlier test result.

This article maps the compliance checkpoints that belong inside a during production inspection for regulated goods: what to verify about materials, what to check on markings, and where the visit hands over to laboratory testing.

Why production threatens earlier approvals

Approval testing examines a golden sample built with care and attention. Mass production optimizes for speed and cost, and every optimization is a chance to drift from the approved configuration. A different solder supplier, a thinner cable, a reworded warning label: each saves money and each can break compliance.

The drift is rarely announced. Factories seldom report that they changed a compound or simplified a marking; they consider it an equivalent choice. The buyer protection is verification on the line: checking that the materials in use match the declared ones and that markings match the approved artwork.

UTS visits this stage as the buyer eyes on the ground. Its inspectors compare what the line actually consumes against the specification the buyer approved, photograph deviations, and pull samples so the laboratory can confirm what eyes cannot see. That independent record is what makes later discussions with the factory factual instead of emotional.

Material controls for restricted substances

The EU restriction on hazardous substances sets maximum concentration values for listed substances in electrical and electronic equipment, applying to homogeneous materials within the product [1]. For production control, the implication is concrete: every plastic, solder, coating, and pigment in the product must come from a compliant grade, and the proof must trace to the batch in use.

Illustration: Material controls for restricted Decorative illustration for the section "Material controls for restricted"; visual only, carries no data.

On the line, the inspector verifies material identity: supplier names, grade markings on reels and drums, and consistency with the declared bill of materials. Declarations and test reports for the input grades should reference the same suppliers and cover the current validity period. A declaration for supplier A means nothing when the line consumes material from supplier B.

The decisive evidence still comes from the laboratory. Production samples drawn by the inspector, sealed and sent for testing, confirm whether the finished product meets the limits. Pre-production approvals cannot substitute for this step because they tested different material. Hold the represented batch until results arrive when the product category or the factory substitution history warrants caution.

Marking and documentation on the line

The CE marking framework requires that products covered by applicable EU legislation bear the marking visibly and legibly, supported by the manufacturer declaration and technical documentation [2]. During production, the checkable elements are the physical ones: presence and proportions of the marking, required warnings, model identification, and the accompanying instructions.

Common production failures include shrunken or distorted marks, missing warnings after artwork simplification, instructions in the wrong language set, and model numbers that do not match the certified variant. Each is cheap to fix on the line and expensive to fix after packing. Verifying first articles of printed packaging and rating plates catches them early.

The inspector should compare production artwork against the approved version character by character, not by overall impression. Font substitutions, reworded warnings, and dropped symbols pass a casual glance and fail a market check. Photograph the marking evidence with scale references so the office can confirm details the site visit cannot settle.

Compliance checkpoints by production stage

StageCompliance checkEvidence to collect
Materials incomingGrade and supplier identity versus declared bill of materialsPhotos of grade markings, supplier labels, delivery lots
Early productionFirst-article marking, warnings, and instructions versus approved artworkComparison photos with discrepancies noted
Mid-runMaterial batch changes, substitution signs, consistency of markingsBatch change log, photos of new lots, re-check notes
Pre-packingFinal marking legibility, language sets, shipping label conformityPacked-carton marking samples, instruction booklet counts
Illustration: Compliance checkpoints by Decorative illustration for the section "Compliance checkpoints by"; visual only, carries no data.

Where the visit hands over to the laboratory

Draw testing samples from the inspected production, not from stock the factory offers separately. Inspector-sealed samples with recorded quantities, dates, and batch links preserve the chain from line to lab. Unsealed or factory-selected samples prove little about the lot under inspection.

Define the hold rule before results arrive: which batches are held, where they are stored, and who authorizes release. A hold without defined boundaries leaks; goods drift into packing while everyone waits for the email. Written hold quantities with the factory acknowledgment keep the boundary intact.

Treat the laboratory result as the verdict and the visit as the context. A pass confirms the sampled configuration; the visit report shows which batches that configuration represents. A failure triggers the standard loop: identify the input or process cause, correct it, and re-test. Shipping regulated goods on a visual pass alone gambles the entire consignment against a test the buyer chose not to run.

Sources

  1. Wikipedia: Restriction of Hazardous Substances Directive —— Overview of the RoHS directive restricting hazardous substances in electrical and electronic equipment.
  2. Wikipedia: CE marking —— Overview of CE marking as conformity marking for products sold in the European Economic Area.

Frequently asked questions

What does RoHS mean for checks during production?

RoHS restricts specific hazardous substances in electrical and electronic equipment sold in the EU, with defined maximum concentrations. During production, the relevant checks are verifying supplier declarations, confirming the correct grades of solder, plastics, and coatings are in use, and pulling samples for laboratory testing. Visual inspection alone cannot confirm chemical composition.

What should inspectors verify about CE marking during production?

The CE marking indicates the manufacturer declaration that the product meets applicable EU requirements; it is not a quality grade or a third-party certificate by default. During production, verify that the marking, required warnings, and instructions match the approved artwork, and that the file references the correct standards. Mismarked goods can be stopped even when the product itself is sound.

What is the role of UTS during a production visit?

UTS acts as an independent third party: its inspectors check the goods against the buyer criteria, document findings with evidence, and report to the buyer. They do not redesign products, issue regulatory certificates, or take over the factory quality duties. Understanding this boundary keeps expectations realistic and the visit productive.

Why test production samples instead of relying on the approval sample?

Because substitution is the classic compliance failure: the approved sample passes testing, then production quietly switches to cheaper non-compliant inputs. Checking material identity on the line and pulling production samples for testing closes this gap. Trust the lab result on production units, not the certificate on the golden sample.

Next step

Bring altitude to your next project.

Book a Flight